Genie M-4700 User Manual download pdf (Page 22)

Transmitter

with Active

Code

New

Transmitter

Light

Blinks

Light

Blinks

Light

Off

Light

Illunimates

Continuously

Press First

and hold

Press Second

and hold

Keep Pressed

Release when

Light Illunimates

Continuously

Midi 2-Channel

Transmitter

Mounting Plate

Visor Clip

Fully Assembled

TRANSMITTER MOUNTING:

The transmitters can be conveniently mounted inside your

car using the mounting plate, or visor clip.

A. Mounting Plate (Fig. 48)

■ Secure the mounting plate to area of preference using

velcro (not provided) or other means.

■ Snap the transmitter into the mounting plate, which will

hold it firmly in place.

B. Visor Clip (Fig. 48)

The visor clip permits easy mounting of transmitter to a visor.

■ Attach visor clip to mounting plate.

■ Snap transmitter into mounting plate.

■ Affix complete assembly to visor.

MULTIPLE TRANSMITTERS:

Each transmitter comes factory programmed with random

codes. 1-channel transmitters have one random code, and

2-channel transmitters have 2 different random codes, one

per button. Transmitters that are purchased separately as

accessories have random codes that must be changed in

order to match the code of the “active” transmitter you are

already using. Below are instructions for transferring an

active code.

■ Remove battery compartment covers of both transmitters,

the one with the active code and the new transmitter that

needs to receive the active code. See Fig. 47.

■ Connect the programming cable to both transmitters.

Line up either end of stripped cable so 3 wires align with

3-hole terminal, then firmly insert cable. See Fig. 49.

■ Press and hold button on transmitter with the active code

((L) in Fig. 49). Midi transmitters have indicator lights that

will blink to show that code transfer is ready.

■ While keeping the transmitter (L) button pressed, press

and hold the button on the new transmitter (R) that you

want to transfer the active code to.

■ Code transfer will occur in approximately 2 seconds. The

indicator light will illuminate continuously to show that

transfer is complete.

■ All buttons can be released. Cable can be removed and

the covers replaced.

■

Both transmitters can now be used to operate the same door.

NOTE: For multi-button transmitters, be sure to carry out

this procedure for all the buttons you desire to use.

CODE CHANGE:

The transmitter factory preset code can be changed as follows:

■

Remove battery cover from compartment.

■

Connect the programming 3-prong cable to programming

terminal in transmitter. (Fig. 50).

■

Cross any two wires of programming cable, one of them must

be the center wire.

■

Press and hold button on the transmitter.

■

Code will change in approximately 2 seconds.

■

Release button after the light illuminates continuously, then-

remove the cable and replace the cover.

Fig. 48

Fig. 49

FCC Certified: This device complies with Part 15 of the FCC rules. Operation is subject to the following

two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible

for compliance could void the user’s authority to operate the equipment.

INSTALLING THE BATTERY (Fig. 47.):

■ Remove battery compartment cover (back of transmitter)

by using small screwdriver.

■ Insert the provided 12V battery (type 23A) as shown.

■ Replace battery compartment cover.

NOTE: Replace batteries with same type only.

10. TRANSMITTERS

Battery

Compartment

Cover

12 V

(type 23A)

Battery

3-Hole

Terminal

Programming

Cable

Fig. 47

NOTE: For multi-button transmitters, be sure to carry out

this procedure for all the buttons you desire to use.

Fig. 50

1 2 ... 17 18 19 20 21 22 23 24 25 26 27 ... 31 32

Comments to this Manuals

No comments

Genie M-4700 User Manual Page 22

Comments to this Manuals

Related products and manuals for Garage Door Opener Genie M-4700