Genie Excelerator User Manual download pdf (Page 23)

A WARNING

A Moving door can cause serious injury or death.

1 Keep people clear of opening while door is moving.

2 Do Not allow children to play with Wireless Keypad.

3 During programming, the door opener could begin

to run, so stay away from the moving door and its

parts.To keep the door from moving, close the door

and disconnect it from the Opener oy pulling the

Emergency Release.

If Safety Reverse does not work properly

1 Close door and disconnect the Opener using

Emergency Release Cord.

2 Do not use door Opener, Remote Controls, or

Wireless Keypad.

3 Refer to Door and Door Opener Owner's Manuals

before attempting any repairs.

NOTE

FOR CONVENIENCE — Program Keypad BEFORE mounting.

A Set Wireless Keypad PIN (Personal ID Number):

• Activate programming mode.

- Press (in order)

- Red LED blinks - once per second.

• Enter your PIN (3 to 8 characters).

• Press

- Red LED blinks - twice per second and turns off.

B Programming One Door Operator:

• Find the Learn Code Button and Learn Code

Indicator LED on your door opener.

- If your door opener has a black antenna

wire, the Learn Code Button and Indicator

LED are located near the antenna.

(The light lens may need to be opened)

- If your door opener does not have an

antenna,you have an external receiver.

The external receiver cover must be

removed to access the Learn Code

Button and Indicator LED.

• Press the Learn Code Button.

- Learn Code Indicator LED (on Opener)

will blink.

• Enter your PIN and press

- Learn Code Indicator LED stays on.

• Press again.

- Learn Code Indicator LED turns off

C Operating One Door Operator:

• To move the garage door:

- Enter your PIN.

- Press(

If the door does not move, check the red LED on

Keypad. If the LED is blinking rapidly, the PIN was

entered incorrectly. After the LED stops blinking,

re-enter your PIN and try again.

Any keypad button will control the door for

30 seconds after the door starts moving.

Rapid Blinking of the red LED indicates an error.

After a few seconds the LED will turn off. Start over.

__________

NOTE

___________

Proceed to"iloijritirig Ifireless ICef fjac!."

Pri3graii'iirJri§ for 2 or 3 Door Operi<?rs

A Set Wireless Keypad PIN (Personal ID Number):

• Activate programming mode.

- Press (in order) ©©©^P-

- Red LED blinks - once per second.

• Enter your PIN (3 to 8 characters).

• Press

- Red LED blinks - twice per second and turns off

B Programming the Keypad for Multiple Door openers:

All sJcicir openers will use the same PIN.

• Enter your PIN and press

- Red LED blinks - once per second.

• Press again.

- Red LED blinks - twice per second.

• Press the number of doors (total) you wish

to control ( or

• Press 1^^^).

- Red LED blinks several times and turns off

Programming Door Openers:

• Decide which door will be door #1, #2 and #3.

• Press the Learn Code Button (see Figure 1).

- Learn Code Indicator LED (on Opener) blinks.

• Enter your PIN and press .

- Learn Code Indicator LED stays on.

• Press the number you have picked for this

- Learn Code Indicator LED stays on.

• Press

- Learn Code Indicator LED turns off.

Repeat step A above for each door opener.

Each door opener must be programmed to receive the

signal from the Wireless Keypad.

FcM' Help, call IHIOOHJS.GEiiE or visit svswi.ferileccirnpiirif.corn

1 2 ... 18 19 20 21 22 23 24 25 26 27 28 ... 31 32

Comments to this Manuals

No comments

Genie Excelerator User Manual Page 23

Comments to this Manuals

Related products and manuals for For the car Genie Excelerator