Genie 4062-TKNMV Instruction Manual download pdf

(A) Powerhead end rail

section

(B) Middle rail section

(D) Door arm, curved

(E) Powerhead lens

(F) Door arm, straight

(G) Mounting straps

(H) Powerhead bracket

(I) Powerhead

(J) Shuttle

(K) Rail connector

(L) Emergency release cord

(M) Safe-T-Beam/wall

console wire

(N) Remote

(O) Wall console

(P) Wireless keypad

(Optional on some models)

Parts List

Potential Hazards

Overhead doors are large, heavy objects that move with the help of springs under high tension and electric motors. Since

moving objects, springs under tension, and electric motors can cause injuries, your safety and the safety of others depends

on you reading the information in this installation poster. If you have questions or do not understand the information

presented, call The Genie Company or your local Genie Factory Authorized Dealer. In this section, and those that follow,

the words Danger, Warning and Caution are used to emphasize important safety information.

Danger:

indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

Warning:

indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

Caution:

indicates a potentially hazardous situation which, if not avoided, may result in injury or property damage.

Note

is used to indicate important steps to be followed or important considerations.

P/N 37067501312

01-11

05-11

ASSEMBLY/INSTALLATION

POSTER

Screw Drive Models

Pre-Installation Considerations

This opener includes parts and supplies needed for installation in MOST garages and on MOST garage doors. There are

many variations of garages and garage doors. A few additional parts and supplies may be needed for installation in YOUR

garage and to YOUR garage door. While going over these instructions, please note the additional items you may need.

For help ﬁnding a local Genie® Professional Dealer, call 1-800-OK-GENIE or Customer Service at 1-800-35-GENIE.

There are a few speciﬁc areas of interest which might require extra materials. They are: 1) The header above the garage

door where torsion springs are used–does it extend far enough above the spring(s) to allow mounting of the header

bracket. If not, or if you can’t tell–you will probably need a piece of 2" x 6" lumber to span across wall studs. 2) The area

overhead where the powerhead will be mounted–if you have a ﬁnished ceiling, you will need a piece of angle iron which

can span across beams of trusses. 3) Is there wood along the door tracks near the ﬂoor where the Safe-T-Beam® can be

most easily mounted, or will you need fasteners for mounting to the track itself or some other material? 4) Measure the

height of your door. If it is taller than 7', you will need a Rail Extension Kit.

Will you need extension brackets or wooden blocks to extend the Safe-T-Beam far enough off the wall to see past any door

hardware?

Is there an electrical outlet within approximately 3' of the point where the powerhead will be? If not, you need to contact a

licensed electrician.

Check condition of the door and all its associated hardware: Tracks, springs, hinges, rollers. Is anything loose or appear

worn? If so, call a trained professional for an evaluation and repairs, if needed. DO NOT ATTEMPT TO ADJUST SPRINGS OR

THEIR ATTACHED PARTS!

Operate the door manually. Does it move freely and smoothly? Check the balance of the door by lifting it by hand

approximately halfway open and let go. It should stay put or move very slowly. If not, call a trained professional for repairs.

Remove all ropes and remove or disable all locks connected to the garage door. It is also recommended that T-handles be

removed. Closed loop lifting handles with no protruding parts can remain.

FPO

Ready to Program

Refer to Operation and Maintenance Manual for programming instructions.

DO NOT run opener until travel limits have been set to avoid damage to unit.

CAUTION

1. Check door height, 8' doors require a Rail Extension Kit (available at leading retail stores)

2. Fully read instructions and warnings before proceeding

TO REDUCE THE RISK OF SEVERE INJURY OR DEATH

READ AND FOLLOW ALL SAFETY, INSTALLATION AND OPERATION INSTRUCTIONS. If you have

any questions or do not understand an instruction, call The Genie® Company or your local

Genie® Factory Authorized Dealer.

• DONOTinstall operator on an improperly balanced door. An improperly balanced door

could cause severe injury. Repairs and adjustments to cables, spring assembly, and other

hardware must be made by a trained service person using proper tools and instructions.

• Remove all ropes, and disable all locks connected to the door before installing operator.

• Install door operator 7 feet or more above the ﬂoor. Mount the emergency release knob

6 feet above the ﬂoor.

• DONOTconnect the operator to the source of power until instructed to do so.

• Locate the wall console button: A) Within sight of door. B) At a minimum height of 5 feet

so small children cannot reach it. C) Away from all moving parts of the door.

• Install the entrapment WARNING label next to the wall button or console. Install the

emergency release tag on, or next to, the emergency release handle.

• The operator must reverse when the door contacts a 1-1/2 inch high object on the ﬂoor

at the center of the doorway. This is about the size of a 2" x 4" board laid ﬂat.

WARNING

An Electrical Shock could result in serious injury or death.

• Turnoffpowerbeforeremovingoperatorcover.

 • Whenreplacingcover,makesurewiresarenotpinchedornearmovingparts.

 • Operatormustbeproperlygrounded.

WARNING

WARNING–HIGH SPRING TENSION

•DONOTtry to remove, repair or adjust springs or anything to which door

spring parts are fastened, such as wood block, steel brackets, cables or other

like items.

• Repairs and adjustments must be made by a trained door system technician

using proper tools and instructions.

WARNING

Need help or have questions? DO NOT RETURN to the store.

Call us: 800-354-3643

A moving door could result in serious injury or death.

• Keep people clear of opening while door is moving.

• DONOTallow children to play with the door operator.

• DONOToperate a door that jams or one that has a broken spring.

WARNING

DOOR A

DOOR B

DOOR C

1a.

1b.

1c.

1d.

1e. 1f.

1a. Slide one rail connector (K) over Powehead end rail section (A) until it locks.

1b. Slide middle rail section (B) into the rail connector (K) until it locks.

1c. Slide second rail connector (K) onto other end of middle rail section (B) until it locks.

1d. Slide door end rail section (C) into the rail connector until it locks.

1f. Secure screw drives of each section with (2) collars and (2) clips.

Rail Assembly

(CLEAR BAG hardware)

Slide collar over

long hook

Slide collar

over joint

Snap clip

behind collar

Mate hooks

Powerhead

rail end

Collar

Clip

Door rail end

Carriage

Grooves

Shuttle

Disengaged

Engaged

Toward door

Grooves along shuttle

ﬁt into rail.

Door Orientation

2a. Place shaft coupler large hole over

screw drive.

2b. Align and slide screw drive/coupler

small hole over motor shaft.

Note: The smaller hole ﬁts over the

motor shaft and larger hole ﬁts over

the drive screw.

2c. Place powerhead bracket (H) on

top of rail with tongue of bracket

inserted into slot on rail. (The rail is

connected with closed side facing

up. The screw will be underneath

and not visible when viewed

from above.)

2d. Align bracket holes with holes on

powerhead (I) and secure with

tapered ﬂange screws. (Use soft

material to cushion underside of

opener in order to protect

powerhead.) Note: Bracket must ﬁt

into slot

Attaching Rail to Powerhead

(BLUE BAG hardware)

Note: To prevent

damage to motion

sensor (not on all

models) DO NOT

remove foam cushion

from underside of

powerhead.

Protective foam cushion

Large

hole

Small

hole

Shaft coupler

1/4"-14 x 3/4"

Tapered ﬂange screw (x6)

Slot

7a. Secure emergency release handle to

cord (L) and attach emergency release

cord to shuttle in rail (J).

7b. Using the emergency release cord,

disengage the shuttle/carriage.

7c. Sectional Doors typically accept

curved door arm (D). In some cases,

straight door arm (F) may be used if

the door bracket is mounted on the

top edge of door.

7d. With the door closed, the angle from door

arm (D) to header is 30˚ max.

Note: One-Piece Door (Top Edge/Face Mount)

instructions are in the Operation and Maintenance Manual provided.

Attaching Door Arm to Door

Bracket and Shuttle

(BLUE BAG hardware)

7c 7c (alt)

7c (alt)

Door bracket

Clevis pin

Cotter pin

Door

Header

3/8"-16 x 7/8"

Bolt &

3/8" Lock nut

Door end rail section

Cotter pin

30° max

Door bracket

Release handle

Orange Bag

3a. Center header bracket above door, mark holes.

3b. Drill two–5/32" pilot holes in header board or 2" x 6" board connected to wall studs.

3c. Secure bracket with lag screws.

Mounting Rail Bracket on Header

(ORANGE BAG hardware)

Header Bracket must be fastened to garage framing. DO NOT fasten to drywall, particle

board, plaster, or other such materials.

CAUTION

Door springs are under high tension. If spring or shaft is in the way, measure above

spring or shaft on the garage door centerline and mark as location for header bracket.

DO NOT ATTEMPT TO MOVE, ADJUST, OR REMOVE DOOR SPRING!

WARNING

**Highest point of door travel plus: Sectional door = Highest point plus 2.5"

One-piece door = Highest point plus 6"

Typical Installation Highest Point of Door Travel

3c 3c

To determine “highest point of door travel”:

1. Get on a ladder to the side of your garage door.

2. Have someone lift the door open slowly.

3. As the door is raised, note the point and amount it extends above the door tracks

with tape measure—that is the highest point of door travel.

4. Measured from ﬂoor to door or from door to ceiling

5/16" x 1-3/4" Lag screw

Highest Point Of Travel

Header

Track

Header

Sectional

Door

Door centerline

Highest point of door travel

(as door is opening) plus**

Header bracket

FROM HERE

TO FLOOR

4a. Elevate opener assembly and position

door end rail section (C) inside bracket.

Note: Support opener and have a second

person assist during this step.

4b. Align holes in rail with holes in bracket.

4c. Slide clevis pin through holes in rail

and bracket and secure with push nut

by pressing the push nut ends together.

4d. Insert rubber plugs into powerhead

accessory holes if present.

Attaching Rail to Bracket

(ORANGE BAG hardware)

Push nut

Protective

foam cushion

Push nut

Rubber plugs

Clevis pin, long

Header

bracket

Sectional Door (Typical):

6a. Center bracket on door, higher than the

top set of door rollers.

6b. Using bracket, mark holes on door or

frame.

6c. Drill 1/8" holes.

6d. Secure with 1/4"–20 x 3/4"

self-drilling screws.

6e. Some garage door manufacturers

provide door brackets that CAN be

used with your Genie Door Arms.

Sectional Door (Wooden):

6a. Center bracket on door, higher than the top set of door rollers.

6b. Using bracket, mark holes on door or frame.

6c. Drill 1/8" holes completely through door.

6d. Fasten bracket with 5/16" x 2"carriage bolts and nuts (not furnished).

Attaching Door Bracket to Door

(ORANGE BAG hardware)

Doors made of masonite, lightweight wood, ﬁberglass, and sheet metal must be properly

braced before mounting door opener. Contact door manufacturer or distributor for any

questions or concerns. The Genie® Company is not responsible for any damage caused

due to an improperly braced door.

CAUTION

Note: One-Piece Door (Top Edge/Face Mount) instructions are in the Operation

and Maintenance Manual provided.

6d 6d (alt) 6d (alt)

Door centerline

Attach no lower than top roller

Door centerline

Top Roller

8a. Position Safe-T-Beam source and sensor on

each side garage door 5"– 6" above ﬂoor.

8b. Mark bracket mounting holes and secure with (4)

1/4" x 1-1/4" lag screws provided into wood. If

mounting into concrete or block, other fasteners are

required and are available at leading retail stores.

8c. Use garage pre-wiring when available or route two

lengths of two conductor wires from powerhead,

through 4 wire clips and ﬁxed to top of rail, across

header, on both left and right of door

down to the source and sensor.

8d. Secure wire to rail with wire clips

spaced evenly along rail, and wire

to header and wall with insulated

staples. Insert wires from above

through control wire tube. Cut off

excess wire.

8e. Attach wire to terminals on each

Safe-T-Beam. At powerhead, twist (2)

striped wires together and insert into

terminal 1 then twist (2) white wires

together and insert into terminal 2. Tape excess wire to powerhead away from lights.

8f. At powerhead, press IN the orange tabs above the terminal to insert the wires with a

ﬂat head screw driver.

Installing Safe-T-Beam

(YELLOW BAG hardware)

When using insulated staples, make only snug enough to hold wire in place. Staples too

tight can cause damage to wire and cause Safe-T-Beam® System to malfunction.

CAUTION

8e 8f

Wall mount

Sensor

Powerhead

To powerhead

Floor mount option

6" max

5" min

above ﬂoor

Source

Sensor/Source

To sensors

Control wire tube

9a. Route wire from powerhead to

desired location for wall console.

Some homes are pre-wired and

they may not be color-coded.

9b. Secure wire with insulating staples

and cut off excess wire.

9c. Attach wires to wall console as

shown.

9d. From above, insert opposite end of

wire through control wire tube on

powerhead and attach as shown.

9e. Mount wall console with #6 screws

9f. Post “ENTRAPMENT WARNING LABEL” (included in

Manual) next to the Wall Console.

Note: Some homes are pre-wired for Safe-T-Beam devices.

Complete the connection and apply power. If the sensor

or wall console LEDs come ON, wire routing is correct.

You may need to wire one sensor at a time to conﬁrm

wire routing in some cases.

Installing Wall Console

(CLEAR BAG hardware)

Use of any other wall control can cause unexpected operation of the door and loss of

lighting feature. Locate wall console within sight of door and far enough from door to

prevent contacting it while operating the console. Control must be at least 5 feet above

ﬂoor to prevent small children from operating it.

WARNING

B/W

White

Striped

To powerhead

To wall

console

To wall

console

Control wire tube

10a. Install light bulbs into powehead (F).

* Note: DO NOT exceed maximum wattage. Each light bulb should be no more than 100W.

(Model 2562 requires light bulbs of no more than 60 watts.)

10b. Insert powerhead lens hinge (E) into slots in motor cover on powerhead (F).

10c. Swing lens (E) up into place. (It may be necessary to squeeze lens slightly to align

tabs with slots at top of motor cover).

Light Assembly

10a

10b

Tab

10c

Each light bulb must be 100 W or less*

Motor Cover

Compact CFL bulbs can be used.

For Grounded Outlet connection:

11a. Plug in the power cord. Coil excess cord and tape or twist tie it to top of

powerhead. (DO NOT PLACE ABOVE LIGHT BULBS.)

For Permanent Wiring by an Electrician:

11a. Cut existing wires OUTSIDE CHASSIS.

11b. The wire connections must be made INSIDE

CHASSIS and there must be at least 6" of

new power supply line wire INSIDE CHASSIS.

(Conduit is optional. Conduit, strain relief, and

wire nuts are not provided.)

Connecting Power

Opener is equipped with grounded electrical plug for your protection, and only ﬁts

grounded electrical outlets. DO NOT alter plug in any way! If you have no grounded

outlets, have one installed by a licensed electrician. Opener must be properly grounded

to prevent personal injury and equipment damage. NEVER USE AN EXTENSION

CORD! Check local building codes for any requirement that you must have a

permanent hard-wired connection. NEVER REMOVE MOTOR COVER. All work inside

cover must be performed by a licensed electrician using proper tools and instructions.

WARNING

11b

Toroid

Hot

Wire nuts

Neutral

Ground

Recommended Tools

12'

1/16"

1/8"

7/16"

1/2"

9/16"

3/8"

1/4"

6' or 7'

Parts Included

BLUE BAG

ORANGE BAG

GREEN BAG CLEAR BAG

YELLOW BAG

Hardware Bags

Cotter pin (x2)

Clevis pin (x2)

Clevis pin, long

5/16" x 1-3/4"

Lag screw (x2)

#8 x 3/4"

Self-tapping

screw (x2)

1/4"x 3/4"

Insulated staple (x30)*

5/16" x 1-3/4"

Lag screw (x2)

5/16"-18 x 3/4"

Bolt (x2)

1/4" x 1-1/4"

Lag screw (x4)

Safe-T-Beam®

sensor

Safe-T-Beam®

source

5/16"-18 Lock nut,

serrated (x2)

1/4"-20 x 3/4"

Self-drilling screw (x3)

Rubber plugs (x2)

Wire clip (x4)

Header bracket

Door bracket Release handle Push nut

Clip (x2) Collar (x2)

3/8" Lock nut (x2)

Shaft coupler

3/8"-16 x 7/8"

Bolt (x2)

1/4"-14 x 3/4"

Tapered ﬂange screw (x6)

5a. Find and mark ceiling at center line of door. For ﬁnished ceilings, attach cross piece

(not supplied) to joists.

5b.

Attach mounting straps (G) to joists or

cross piece with (2) lag screws (5/16" x

1-3/4") provided in green bag.

5c. While supporting opener unit, open door

and raise opener unit to clear door so it

passes the rail clearly.

5d. Secure opener unit (in position) to

mounting straps with nuts and bolts.

Mounting Powerhead

to Ceiling

(GREEN BAG hardware)

Note: Rail should be level to ﬂoor. For tall garage ceilings additional hanging angle

and hardware may be required and is available at leading retail stores.

Open Beam Ceiling Finished Ceiling

Door centerline

To cross piece (center of opener)

Cross piece

location

114"

Attach

to joists

Lag screws

5/16" x 18 x 3/4"

Bolt (not included)

5/16" x 18

Nut

5/16" x

18 x 3/4"

Bolt

Lag screws

Hidden joists

Lag screw

Cross piece

(not included)

Screw Drive Models 1

Summary of Contents

Page 1 - Screw Drive Models

ABC(A) Powerhead end rail section(B) Middle rail section(C) Door end rail section(D) Door arm, curved(E) Powerhead lens(F) Door arm, straight(G)

Comments to this Manuals

No comments

Genie 4062-TKNMV Instruction Manual

Browse online or download Instruction Manual for Unknown Genie 4062-TKNMV. Genie 4062-TKNMV Instructions / Assembly User Manual

Summary of Contents

Comments to this Manuals