Genie INTELLIG 3024 User Manual Page 19

  • Download
  • Add to my manuals
  • Print
  • Page
    / 26
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 18
©2010 The Genie Company 01/27/2010
19
Independent Light Control Button
– Controls door opener lights from inside garage
– Shuts OFF lights 4 minutes after door action
Vacation Lock Button
– LOCK disables controls
after door is completely
closed
– UNLOCK allows controls to
work normally
Indicator Light
Red indicator light is always ON
When Vacation Lock is ON the
indicator light flashes
Open/Close Button
Open and closes door from inside garage
WALL CONSOLE - OVERVIEW
Use only the Series III wall console provided with this
unit. Wall consoles from other manufacturers will not
work with this power head.
Earlier Genie® Series II
wall consoles will not work with this power head
.
Wall console has three buttons and one indicator light.
Indicator Light
Indicator light will display red when wall console
is properly wired and Vacation Lock is OFF. When
Vacation Lock is ON indicator light flashes.
Open/Close Button
Use this button to open or close garage door. When
Vacation Lock is ON the Open/Close button will
CLOSE door only. Note: Constant button pressure in
the CLOSE mode will override error responses in the
power head and close door.
Independent Light Control Button
Use this button to turn power head lights ON. Power
head lighting will remain ON until this button is
pressed again or a door action has been completed.
Note: If opener has a Motion Detector sensor the
sensor will keep power head lights ON as long as
motion is detected.
Vacation Lock Button
When Vacation Lock is ON the power head cannot be
activated by the wall console or a remote.
• Press and hold for 5 seconds (or till Indicator Light
flashes) to activate Vacation Lock.
• Press and release to turn Vacation Lock OFF.
OPTIONAL DUAL WALL CONSOLE - INSTALLATION
Use only the Series III wall console provided with this
unit. An optional second
Genie® Series III wall console
(not provided) can be added.
OR
STB BWC IWC
NOT
USED
NOT
USED
FROM STBs
FROM WALL
CONSOLE #1
FROM WALL
CONSOLE #2
TO
POWER HEAD
WALL
CONSOLE #1
WALL
CONSOLE #2
TO WALL CONSOLE #1
W
B/W
W
B/W
W
B/W
W
B/W
BOTH TO POWER HEAD
WALL
CONSOLE #1
WALL
CONSOLE #2
STB BWC IWC
NOT
USED
NOT
USED
NOT
USED
NOT
USED
FROM STBs
FROM WALL
CONSOLE
Tip: If indicator light on wall console comes ON, but
there is NO
operation from
buttons -
verify
wall console
wire
routing
at power head
connector.
STB BWC IWC
NOT
USED
NOT
USED
NOT
USED
NOT
USED
FROM STBs
FROM WALL
CONSOLE
STB BWC IWC
FRO STBs
FROM WALL
CONSOLE
STB
BWC
IWC
OM STBs
ROM WA
OM W
OLE
ONSO
CHANGE LIGHT BULBS
WARNING
Observe all safety warning and precautions!
Improper light bulb removal or replacement
could result in Death or Serious Injury.
Disconnect power from opener before
beginning this task.
When replacing light cover, make sure wires are
not pinched or near moving parts.
1. Disconnect power to door opener.
• Open power head light cover.
• Remove light bulb(s).
• Replace with maximum 100 Watt light bulbs.
Do NOT use light bulbs with greater than 100
Watt rating.
• Close power head light cover.
2. Reconnect power to door opener.
Test light operation.
Page view 18
1 2 ... 14 15 16 17 18 19 20 21 22 23 24 25 26

Comments to this Manuals

No comments