Genie AR90 User Manual download pdf (Page 4)

Slide the GDK onto the screw, see

figure 6.

Figure 6

If your original transmitter has two or three

buttons and uses DIP switches, set the

LED in the GDK to the opposite position

on the first DIP switch of your original

transmitter. Set the remaining GDK LEDs

to the exact same position of your original

transmitter’s DIP switches. If your original

transmitter has two or three buttons but

does not have DIP switches inside the

original

transmitter or if the original

transmitter is lost or broken, please use

the DIP switches located on the radio

receiver (near the head unit) or at the push

button located on the garage wall. The

radio receiver can be found on or near the

garage door opener motor head mounted

your garage

ceiling.

The

DIP

switches

are usually located near the point where

the electrical enter the garage door opener

head or on the externally mounted radio

receiver. YOU DO NOT NEED TO

DISASSEMBLE THE GARAGE DOOR

HEAD OR RADIO RECEIVER TO

LOCATE THE DIP SWITCHES,

HOWEVER, YOU MAY HAVE TO

REMOVE THE PROTECTIVE COVER.

The GDK should be mounted to an outside

wall, close to your Garage Door. Mount

the GDK on a flat vertical surface with

enough room above the GDK to slide the

cover up. The location should be easily

reached by anyone who will use it, at least

five feet above the floor and clear of any

moving Garage Door parts. It is

recommended that you choose a location

that is not in direct sunlight. If you mount

the GDK in a location that is exposed to

direct sunlight, the LEDs will be difficult to

see. It is also recommended that you do

not mount the GDK onto a metal surface,

as this may reduce the range of the signal.

To mount the GDK:

Using one of the supplied

1”

screws, drive the screw into the

wall in your chosen location,

leaving

1/4”

of the screw

protruding from the wall.

Remove the battery cover and

disconnect the battery. This will not

erase the passwords or security

codes already stored in the

GDK’s

memory.

Drive the second

1”

screw through

the hole at the rear of the battery

compartment.

Remove the battery cover and

disconnect the battery. This will not

erase the passwords or security

codes already stored in the

GDK’s

memory.

Drive the second 1" screw through

the hole at the rear of the battery

compartment.

Figure 7

Insert Screw

NOTE:

Make sure that the GDK is aligned

in an upright position before driving in the

second screw.

Re-attach the battery and slide

battery cover back into place.

After you have stored your garage door

opener(s) security codes in the memory

the GDK and you have mounted the unit

you are ready to use your GDK. To open

your garage door:

1. PIN

Open the

GDK’s

cover or, if

the

cover is already open, press

ENTER. Key in your PIN, then

press ENTER. The GDK will beep.

NOTE: If you enter an incorrect PIN the

times, the GDK will lock you out for on.

minute. After one minute, re-enter the

correct PIN to proceed with opening you

garage door.

Press DOOR1, DOOR2 or

DOOR3, depending on which door

you would like to open. The GDK

will send a signal to your garage

door opener for as long as the

DOOR1 , DOOR2 or DOOR3 key

is pressed. Once you release one

of the keys, the signal will stop.

Your garage door will open. Thirty

seconds after the last key press,

the GDK will power off.

NOTE:

After selecting the door

operated by pressing DOOR1 , DOOR2 or

DOOR3, pressing any key other

than EXIT

will open or close that specific garage

door.

If, after opening DOOR1, you

would then like to open DOOR2 or

DOOR3, press the EXIT key once

and then press DOOR2 or DOOR3

to open another door.

Do NOT allow children to play with

the transmitter or door opener, If

children must use the GDK, please

supply proper training first.

Keep people clear of the garage

door as it is opening and closing.

The garage door could cause

serious injury or death.

Use the GDK only when you are

sure that all possible obstructions

have been removed.

Smarthome.com, Inc. (800) SMART-HOME (949) 221-9200 http://smarthome.com

1 2 3 4 5

END PANEL 3
ELECTRONICS 5

Comments to this Manuals

No comments

Genie AR90 User Manual Page 4

Comments to this Manuals

Related products and manuals for Garage Door Opener Genie AR90