Genie AR90 User Manual download pdf (Page 2)

1.

2.

mx8

oo*I

Slide open the cover. The GDK’s

keypad will illuminate.

Press the number 9 eight times, then

press ENTER, the GDK will beep

once and the green LED will

w

illuminate for two seconds followed

by two quick beeps. The GDK will

power OFF. This clears the GDK of

any previous passwords and

securitycodes so that you can

begin a new setup. Your GDK has

now ready to learn your new

password and garage door security

code(s).

NOTE: Use the reset code only

to

clear

the GDK of all passwords and garage door

security codes.

1.

Select a PIN (Personal Identifica-

tion Number) and write it down.

This will be your password. Your

PIN can be up to 8 digits long.

Press the ENTERkey to illuminate

&

the GDK’s keypad.

3.

w

Press tne

number 1 (Factory

’

Default Password) followed by

v

ENTER. The green LED will blink

two times followed by one beep.

The GDK is now on and ready to

learn your new password (PIN).

Pres

s STORE followed by the

PlN1, PIN2* or PIN3* key. The first

red LED, corresponding to PIN1,

will light and remain lit as the

green LED blinks.

*NOTE:

The first time you enter a

password, GDK automatically defaults that

password to PIN1, even if PIN2 or PIN3 is

pressed.

5.

PIN

Enter the PIN you wrote down in

B

STEP 1 then press ENTER. The

GDK will emit a double-ticking sound

to prompt you to confirm your new

PIN

password. Now reenter the PIN and

w

press ENTER again. If you entered

the

same PIN correctly, the green

LED will illuminate for three seconds

followed by two beeps. The GDK will

then power OFF.

NOTE:

If

you make a mistake in entering

your PIN, press the EXIT key and return to

STEP 2 to re-enter your new

PIN.

You will need your original garage door

opener when setting up GDK’s garage

door security code. Open your original

garage door opener so that you can view

the DIP switches.

1

.PlN

Open the GDK’s cover or, if the

w

cover is already open, press

ENTER. Key in your PIN followed

by ENTER. The GDK will beep and

the green light will blink twice if the

PIN is correctly entered. If you

enter your PIN incorrectly, the GDK

will beep and the red light will blink

once.

Press STORE followed by

DOOR1,

DOOR2 or DOOR3. The

first six

LEDs

will chase. Enter the

number (1-6) from the table for

your brand of garage door

opener (See Figure 4). The

corresponding LED will light.

NOTE:

If

you make a mistake during the set

up

process,

press the EXIT key, re-enter your

PIN and return to

step 1 in

the

"SETTlNG

UP

THE

SECURITY CODE TO OPERATE

YOUR

GARAGE

DOOR" section

to

re-enter

your garage door opener’s code.

I

MULTI-CODE

AMBASSADOR

MULTI EL MAC

MOORE-O-MATIC

LINEAR

DELTA

SHIMA

POWERLIFT

3

GENIE MODEL

AT90

GENIE MODEL

SD9500

LIFTADOOR

BLUE MAX

EZ LIFT

4

GENIE MODEL

AR85

5

CHAMBERLAIN

SEARS

RAYNOR

LIFT-MASTER

WAYNE DALTON

MASTER

MECHANIC

STANLEY

6

AUTOMATIC

DOORMAN

VEMCO

10

BITS/300

MHZ

8

BITS/310

MHZ

12

BITS/390

MHZ

9

BITS/390

MHZ

9

BITS/390

MHZ

TERTIARY BITS

10

BITS/31

0 MHZ

3.

Press ENTER. All of the

LEDs

will

w

begin to chase, then the first LED

will blink.

Using the UP, MID and DOWN

keys, match the

LEDs

to the DIP

switches in your original garage

door opener. When you press UP,

the LED will remain on. When you

press MID, the LED will flash

slowly and when you press

DOWN, the LED will remain off.

NOTE: The

LEDs must m

atch exactly to

the

DIP switches on your original garage

door opener.

Smarthome.com, Inc. (800) SMART-HOME (949) 221-9200 http://smarthome.com

1 2 3 4 5

END PANEL 3
ELECTRONICS 5

Comments to this Manuals

No comments