©2011 The Genie Company9/2011 10
ADJUSTMENT GUIDE - FORCE SETTINGS
Force settings are pre-programmed at the factory and
"learned" during the Open/Close Limit settings steps.
For normal use, these settings should not need adjustment
with this unit.
However, conditions possibly requiring adjustment are:
Doors with very stiff weather seals.
Doors that start down, STOP and reverse before closing.
Doors that start up, but STOP before they completely open.
CAUTION
Door closing force is FACTORY set and requires no
adjustment for normal operation.
s
Never adjust the force settings to compensate for damage,
including an unbalanced door, binding door track or
broken spring.
s
Perform monthly CONTACT REVERSE
LED indicator colors
OFF
Blue
Purple Red
1.
2.
3.
ADJUSTMENT GUIDE - SPEED SETTINGS
Speed settings are pre-programmed at the factory for the
maximum speed. Speed settings should not need adjustment
with this unit.
However, travel speed for the opener can be adjusted to a
slower speed in both the open and close directions, To
mimimize wear on heavier sectional doors.
NOTE: One-piece doors are automatically set to the slowest
speed during Limits programming and cannot be adjusted.
There are 3 speed settings available for sectional doors.
Please note that speed may be affected by door weight and
balance, along with condition of door components and tracks.
TEST. See page 7.
Press & hold
both up and
down buttons
2 seconds or until round
LED turns Red.
Press &
Release.
Press either
until you reach
desired setting.
FORCE SETTINGS DONE
PROGRAM
SET
Press &
Release.
PROGRAM
SET
FORCE ADJUSTMENT
1
2
3
4
5
USE CHART BELOW.
Press either
until you
reach the
desired setting.
USE CHART BELOW.
LOCKS IN SETTING.
LOCKS IN SETTING.
OFF
OFF
Speed Level
Powerhead LEDs
ROUND LED
LONG LED
LED indicator colors
OFF
Blue
Purple Red
High
Medium
Low
RED
RED
PURPLE
PURPLE
ACTION LED INDICATION/RESULT
Then the Current UP FORCE
SETTING will display. SEE CHART.
Then the Current
DOWN FORCE
SETTING will display.
Both LEDs TURN
BLUE then OFF
confirms Force
Settings are reset.
Both LEDs FLASH
BLUE to confirm setting.
Press &
Release.
Press twice.
FORCE SETTINGS DONE
PROGRAM
SET
Press & Hold for
about 10 seconds
or until both LEDs
turn Blue.
Then release.
PROGRAM
SET
Press &
Release.
PROGRAM
SET
SPEED ADJUSTMENT
1
2
3
4
5
Press &
Release.
PROGRAM
SET
Press either until
you reach the
desired setting.
LOCKS IN OPENING SETTING.
LOCKS IN CLOSING SETTING.
OFF
ACTION LED INDICATION/RESULT
Then the Current Speed setting
for OPENING travel will display.
SEE CHART BELOW.
Then the Current Speed setting
for CLOSING travel will display.
SEE CHART BELOW.
NOTE: Depending on the criteria
mentioned above, you may not
have the option to increase speed.
Press either until
you reach the
desired setting.
NOTE: Depending on the criteria
mentioned above, you may not
have the option to increase speed.
BLUE
OFF
RED
OFF
BLUE
FLASHES 3 TIMES
OFF
FLASHES BLUE 3 TIMES
BLUE
BLUE
BLUE
FLASH BLUE
FLASH BLUE
BLUE
BLUE
BLUE
BLUE
FLASHES
BLUE 3 TIMES
OFF
BLUE
FLASHING
BLUE BLUE
7
6
Force Level
Powerhead LEDs
ROUND LED
LONG LED
BLUE
BLUE
BLUE BLUE
Off
Off
Off
Off
PURPLE
PURPLE
PURPLE
PURPLE
Off
RED
RED
RED
RED
Off
(32 pages)
(29 pages)
(26 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals