3531835447fKaimm———Safety Information...2Important Installation Instructions...2Safety
A Place Magnetic Carriage Assembly Lever in "release" position.B Slide Magnetic Carriage Assembly into slot on End Rail Section with arrow p
NOTELoosen (Do Not Remowe) Terminal Block Screws. Limit Switch adjustments and securing the Wires will be done later.F Lay Wires in channel on top of
Mount directly into headerUse of Header Bracket support boardNOTEFor lightweight garage doors, make sure you have installed the proper reinforcement (
A CAUTIONDoors made of masonite, lightweight wood, fiberglass, metal, or other lightweight materials must be properly braced before mounting door Open
A Raise and support Opener Power Head (along door center line) higher than highest point of door travel (using step ladder, etc.) (Figure 21).B Measur
For stictiorial cii3ors:A Attach Curved Door Arm to Door Bracket with Clevis Pin and Cotter Pin (Figure 23).B Attach Straight Door Arm to Magnetic Car
Safe-T-Beam® Sensor (Green LED)@)^ ELECTRICAL WARNINGEnsure there is No power to the Opener before installing Safe-T-Beam® System Wires. If Opener is
^ CAUTIONStaples which are too tight may cut or pinch Wires. Cut or pinched Wires can cause the Safe-T-Beam® System to stop working. When installing t
SecurityVacationA WARNINGVerify there is no power to the Opener before installing Wall Console Wires. * •NOTEMore than one lighted Wall Control per Op
A electrical warningTo reduce the risk of electrical shock, this equipment has a grounding type Plug that has a third (grounoing) Pin. This Plug will
Garage Doors are heavy objects that move with the help of springs under high tension and electric opening equipment. Since moving objects, springs und
Setting Close Limit Switch (Figure 34):• Check that Magnetic Carriage Assembly is disengaged.• With garage door fully closed, slide Close Limit Swit
To protect your new investment, your Excelerator® is equipped with a Timer and Cycle Counter which work together to prevent any chance of heat damage
A To program one Button of a Remote Control (Figure 37):• Locate Learn Button and Learn Indicator Light near Terminal Block on Power Head (Figure 38)
A WARNINGA Moving door can cause serious injury or death.1 Keep people clear of opening while door is moving.2 Do Not allow children to play with Wi
(Continued)Operating 2 or 3 Door Openers:• To move one of the doors.• Enter your PIN.• Press ,Press door opener number (C1J or orMount Keypad. (Mo
Snap Lens Hinges into slots on back of Motor Cover60 WattsmaximumBCFigure 41 Install Lens Cover and Light BulbsInstall two 50 Watt light bulbs (not in
^WARNING TO REDUCE THE RISK OF SEVERE INJURY OR DEATH1 READ AND FOLLOW ALL INSTRUCTIONS.2 Never let children operate or play with the Door Controls.
OfSee Status Light on FigureSS, page 22)u See ablem /Vhat to Do Reference1 BLINK, 1 Motor DriveeReset Opener—unplug (or disconnect power), wait 5 seco
ProblemOpener does not run from Remote ControlDoor Opener starts for no apparent reasonDoor starts down, then stops before it is Icompletely closed ID
C5eri<iral Troubleshooting (Al'imafs Chtick th<i Steitus LED UghtMCoritIriuecllLi'Oblc.iV; What To DoRemote Control has less«Relocate
This Opener includes parts and supplies needed to install in most garages and connect to most garage doors. There are many variations of garages and g
What is CmemdAny defect in material and workmanship from personal, normal household use in accordance with the Owner’s Manual.For How Long:;H8000D Ser
ài(GIT-1) Deluxe Remote Control with Intellicode®- Allows remote operation of garage door Controlador remoto de lujo con Intellicode®- Proporcionar op
I&MODELMODELOMODÈLEDESCRIPTIONDESCRIPCIÓNDESCRIPTIONPRODUCT CODE CÓDIGOCODE DU PRODUITPRICE (US$)* PRECIO* PRIX ($ US)*QTY.CANTIDADOTÉTOTALTOTALTO
Measure garage door height (7'-6", 8'-0", or taller) with tape measure.A If door height is 7'-6" or less, continue with
Check ceiling or space above where Opener Power Head will be mounted (Figure 5):A Measure from garage door center line mark toward rear of g
Check for wood garage frame, jamb, or masonry at mounting location (6" above floor) with attachment tabs facing away from garage door (Figure 7).
Item Part Name QuaReqi1-Pc Railutitylired3-Pc Rail1 Power Head Assembly (main carton) 1 12 1 /4"-20 X13/16" Hex Head Shoulder Bolt (blue bag
_________________________NOTE________________Opener will not function unless Safe-T-Beam® System is installed and Force Controls are properly set.One-
A Turn Power Head upside down and place on a flat level surface.B Install Bumper (Figure 9).C Install Coupler on Motor Shaft (Figure 9).A CAUTIONThe D
Comments to this Manuals